TL-333

スイッチ付きマグネットキャッチ

Magnetic Catch with Switch
¥1,078(税込)
数量:
日本語
ENGLISH
特長
扉の開閉によりスイッチがON・OFFできます。マグネットキャッチにマイクロスイッチが内蔵されているため、検知をコンパクトに一体化できました。検知スイッチ部が太く、小型でも丈夫です。
Characteristic
Opening or closing the door makes the switch on / off. A limit switch is set inside of the magnet catch to get holding / detection together. Tough and small.
用途
工作機械(設備カバー)・OA機器・収納庫・クローゼット・その他防犯用扉
Application
Machine Tools (Cover) / Office Automation Appliance / Shed / Closet / Security Doors
仕様
1.スイッチ性能
・接点形式:保持と切換型(回路図参照)
・定格
定格電圧 抵抗負荷
AC125V 3A
DC30V 3A
・絶縁抵抗 100[MΩ]以上(DC500[V]絶縁抵抗計にて)
・耐電圧 非連続端子間 AC1000[V]/1分間
 各端子と非連続金属部間 AC1500[V]/1分間
 各端子とアース間 AC1500[V]/1分間
・電気的寿命 7万回以上(開閉頻度20回/分)

2.マグネット
・吸着力 約19.6N(2kgf)以上(附属のキーパー使用時)

3.環境
・使用周囲温度 -25℃~85℃(氷結・結露無きこと)
Specification
1.Specification of Micro switch
・Contact arrangement Switch-over(Please see Circuit Diagram)
・Rating
Rated voltage Resistance Load
AC125V 3A
DC30V 3A
・Insulation Resistance 100MΩ Min.(at 500V DC Megger)
Dielectric Strength:
 Between unconnected terminal 1000V AC/ min.
 Between terminal and unconnected metal plate 1500V AC/ min
 Betwen Current-Carrying Metal Part and Ground 1500V AC/min.
 Electrical Life Expectancy  70,000 Operations Min.

2.Magnet
・Holding Force approx. 19.6N(2kgf) or more(with attached keeper)

3.Environment
・Ambient Operating Temperatures Range
 -25℃ to 85℃(No frozen and dew condensation.)
注意事項
引火性ガス、腐食性ガス、シリコン等の多い雰囲気、又、極端に塵埃が堆積する様な場所での使用、保管は避けて下さい。
本マグネットキャッチが扉等の可動部のストッパーとなり全ての荷重を受けるような取り付けはお避けください。スイッチ部が破損する場合があります。
端子部にはんだを施す場合、はんだゴテ先温度350℃以下にて3秒以内に作業を終了し、作業中及び作業後1分間は端子部に力が加わらないようにしてください。
本体は、検知スイッチ部に斜め方向から荷重が加わらない様に取り付けてください。
キーパーの取り付けには、M3の皿ネジを用いて下さい。また、取付側にC1の面取りを設けてください(キーパーの取付図参照)。
Note
Avoid using or storing in a condition with inflammable gas, corrosive gas or silicon rich atmosphere, also in an excessively dust place.
This product can not be used as a stopper.Please install stopper separately.
Manual soldering should be accomplished within 3 seconds with max. 350℃ iron. Care should be taken not to apply force to the Terminals during soldering. Terminal portions must not be moved in 1 minute after soldering.
Please avoid adding load to switch part from oblique angle when installing.
Use M3 screw to install keeper. Installation holes should be chamfered.